How to install hinged doors - how to install hinges

 

How to install the hinge - the installation steps of the hinge

 

1. The installation distance is generally determined according to the thickness of the door panel. For example, if the thickness of the door panel is 19 mm, then the edge distance of the hinge cup is 4 mm, and the minimum edge distance is 2 mm. Let me take you to understand the installation steps.

 

2. After determining the distance between the installed door panel and the hinge, we will actually install it according to the number of cabinet door hinges selected. The number of installed hinges mainly depends on the height of the installed door panel. The general height is 1500mm and the weight is For door panels between 9-12kg, you should choose about 3 hinges.

 

3. When the cabinet door is connected and installed, the installation method is also very important. According to the position of the door side and the side panel side, there are three installation methods: full cover door, half cover door and embedded door. The full cover is generally It covers the side panels, and the half-cover door covers half of the side panels, especially suitable for cabinets with partitions in the middle that need to install more than three doors, and the embedded doors are installed in the side panels.

 

4. When the door is installed and connected, we first need to use a measuring class or a carpenter's pencil to determine the position, and the drilling margin is generally about 5mm, and then use a pistol drill or a woodworking hole opener to make an approximate hole on the door panel. 35 mm installation hole, the drilling depth is generally about 12 mm, and then put the door hinge into the hinge cup hole on the door panel and fix the hinge cup with self-tapping screws.

 

5. Then we insert the door hinge into the cup hole of the door panel and open the hinge, then put it in and align the side panel, and fix the base with self-tapping screws. After all these are done here, we will try the effect of opening the door. The door hinges can be adjusted in six directions, and they must be aligned up and down. The left and right positions of the two doors are moderate. Generally, the distance between the closed doors after installation is about 2 mm.

 

How to install the hinge - precautions for hinge installation

 

1. Before installation, it should be observed whether the parts that need to be connected by the hinge are consistent.

 

2. Check whether the length and width of the hinge and the connection are appropriate. If they share one side plate, the total interval to be left should be the two minimum intervals.

 

3. If the coverage distance of the fixed machinery is correspondingly reduced, a hinge with a bent arm is required.

 

4. When linking, check whether the hinges are compatible with the connecting screws and fasteners. Dont be one kind of thing. The maximum size of each kind of hinge is selected according to the type of conveyor.

 

5. When installing the hinge, it should be ensured that the hinge is on the same vertical line as the fixed object, so as to avoid misalignment of the mechanical object or wear of the conveyor due to unstable fixation.

 

 

How to Install Cabinet Door Hinges

 

During the use of the cabinet, the most tested thing is the cabinet door hinge. If the installation of the cabinet door hinge is unreasonable, it will inevitably bring unnecessary troubles. So how to install the cabinet door hinge? I will teach you today.

 

 

•  

01

Determine the size of the cabinet door. After determining the size of the cabinet door, it is necessary to determine the minimum margin between the installed cabinet doors. This is generally listed on the cabinet hinge installation manual. You can refer to the determined value. If the minimum margin is not done properly If it is not, it is easy to cause the cabinet door to collide, which will affect the beauty of the cabinet and is not practical.

 

 

•  

 

02

Selection of the number of hinges. The number of cabinet links selected should be determined according to the actual installation time. The number of hinges used for the door panel depends on the width and height of the door panel, the weight of the door panel, and the material of the door panel. For example: the height is 1500mm, and the weight is 9-12kg Between the door panels, 3 hinges should be selected.

 

 

•  

 

03

After determining the value and number of cabinet hinges, when the hinges are connected, we use the installation measuring board to mark the position, and then drill the hinge cup mounting holes with a width of about 10 mm on the cabinet door with a pistol. The depth of the drilling is Generally around 50mm.

 

 

•  

 

04

Install the hinge cup. First fix the hinge cup with self-tapping screws with flat countersunk head particleboard, because the hinge cup will bulge, you can use a machine to press the hinge cup into the door panel, then use the pre-drilled hole to fix it, and finally use a screwdriver to rotate it The expansion screw fully fixes the hinge cup.

 

 

•  

 

05

Install the hinge hinge seat. Try to choose the European-style special screw for particle board or the pre-installed special expansion plug to fix the screw, and then directly press it in with the machine.

 

 

•  

 

06

Hinge adjustment. Generally, door hinges can be adjusted in six directions, aligned up and down, and the left and right positions of the two doors are moderate. The distance between the doors after installation is generally about 2mm.

 

 

•  

 

Hinge installation precautions

•  

01

Before installation, it should be observed whether the parts that need to be connected by the hinge are consistent.

 

 

•  

 

02

When linking, check whether the hinge is matched with the connecting screws and fasteners. The maximum size available for each hinge is selected according to the type of conveyor. If the coverage distance of the fixed machinery is correspondingly reduced, it is necessary to use A hinge with a bent arm.

 

 

•  

 

03

When installing the hinge, it is necessary to ensure that the hinge and the fixed object are on the same vertical line, so as to avoid the misalignment of the mechanical object or the wear of the conveyor due to unstable fixing.

•  

  There is another name for cabinet door hinges called hinges. This is mainly used to connect our cabinets and our cabinet doors. It is also a common hardware accessory. Cabinet door hinges are used in our cabinets. Time is very important. We open and close many times a day, and the pressure on the door hinge is very great. Many people don't know how to install it after buying it. Today I will introduce you to the installation of the cabinet door hinge. method.

   

   

 

 

the

Introduction to the installation method of the cabinet door hinge

 

 

Installation method and method

 

 

Full cover: The door completely covers the side panel of the cabinet body, and there is a certain gap between the two, so that the door can be opened safely.

 

 

Half cover: Two doors share a cabinet side panel, there is a required minimum gap between them, the coverage distance of each door is reduced, and a hinge with hinge arm bending is required. The middle bend is 9.5MM.

 

 

Inside: The door is located inside the cabinet, beside the side panel of the cabinet body, it also needs a gap to facilitate the safe opening of the door. A hinge with a very curved hinge arm is required. The big bend is 16MM.

 

 

First of all, we need to install the hinge cup. We can use screws to fix it, but the screws we choose need to use flat countersunk head chipboard self-tapping screws. We can use this kind of screw to fix the hinge cup. Of course, we can also use Tool-free, our hinge cup has an eccentric expansion plug, so we use our hands to press it into the pre-opened hole of the entry panel, and then pull the decorative cover to install the hinge cup, the same unloading The same is true of time.

 

 

After the hinge cup is installed, we still need to install the hinge seat. When we install the hinge seat, we can also use screws. We still choose particleboard screws, or we can use European-style special screws, or some pre-installed special expansion plugs. Then the hinge seat can be fixed and installed. There is another way for us to install the hinge seat is the press-fitting type. We use a special machine for the hinge seat expansion plug and then press it in directly, which is very convenient.

 

 

 

Finally, we need to install the cabinet door hinges. If we dont have tools for installation, it is recommended that you use this tool-free installation method for cabinet door hinges. This method is very suitable for quick-installed cabinet door hinges, which can be used The way of locking, so that it can be done without any tools. We first need to connect the hinge base and the hinge arm at our lower left position, and then we buckle down the tail of the hinge arm, and then Gently press the hinge arm to complete the installation. If we want to open it, we only need to press lightly on the left empty space to open the hinge arm.

 

 

We use a lot of cabinet door hinges, so after a long time of use, it is inevitable that there will be rust, and if the cabinet door is not closed tightly, then we'd better replace it with a new one, so that we can use it with more confidence.

 

 

 

Cabinet door hinge installation method:

 

 

1. Minimum door margin:

 

 

First of all, we need to determine the minimum door margin between the cabinet doors to be installed, otherwise the two doors are always "fighting", which is not beautiful and practical. The minimum door margin depends on the type of hinge, hinge cup margin and cabinet Select the value based on the thickness of the door. For example: the thickness of the door panel is 19mm, and the edge distance of the hinge cup is 4mm, so the minimum door edge distance is 2mm.

 

 

2. Selection of the number of hinges

 

 

The number of cabinet links selected should be determined according to the actual installation experiment. The number of hinges used for the door panel depends on the width and height of the door panel, the weight of the door panel, and the material of the door panel. For example: a door panel with a height of 1500mm and a weight between 9-12kg, 3 hinges should be used.

 

 

 

 

 

3. Hinges adapted to the shape of the cabinet:

 

 

The cabinet with two built-in rotatable pull baskets needs to fix the door panel and the door frame at the same time. The most important thing is that the built-in pull basket determines its opening angle to be very large, so the curvature of the hinge must be large enough to ensure that it can Freely open the cabinet door to a suitable angle, and conveniently take and place any items.

 

 

4. Selection of hinge installation method:

 

 

The door is divided according to the position of the door side and the side of the side panel, and there are three installation methods: full cover door, half cover door and embedded door. The full cover door basically covers the side panel; the half cover door covers the side panel. The half of the board is especially suitable for cabinets with partitions in the middle that need to install more than three doors; the embedded doors are installed in the side boards.

 

 

The above is the installation method of the cabinet door hinge introduced to you. Are you clear? In fact, the installation of the cabinet door hinge is very simple, we can install it without tools, but if you dont know what to do after reading the above How to install it, I suggest that you better find someone to install it, so that you can be more assured, and will not cause any problems in your life after the installation is not good. How to install the wardrobe door hinge The simple installation skills are here

 

 

1. First, fix our hinges on one side of our cabinet door. Pay attention to flushness, generally there are reserved holes.

 

 

 

2. After that, we put our cabinet door vertically on the top of our cabinet, and plug the reserved position with cardboard on both sides.

 

 

 

3. After that, screw on our horizontally movable screw ports, one for each hinge.

 

 

 

4. Control the door of our cabinet in the central position of our cabinet by moving it. Ensure that the switch is convenient.

 

 

 

5. After that, screw all our screw holes with our screws and tighten them. Then start to adjust.

 

 

 

6. One of our hinges has two longitudinal screws. We adjust the bottom one to elongate our hinge, which avoids our cabinet door and cabinet bumping.

 

 

 

7. After that, adjust our second screw to adjust the up and down deformation of our cabinet door. If it cannot be closed, it means that the screw has not been adjusted properly. Finally, adjust our cabinet door hinge and install it.

 

36 thick door 175 degree hinge installation skills

 

36 thick door 175 degree hinge installation skills have the following five steps.

 

1. Determine the distance and installation quantity. Before installation, determine the distance between the doors, control the distance between the door panel and the cabinet, prevent problems such as collisions and inability to open and close after installation, and determine the number of hinges installed on the door panel , the number of hinges should be determined according to the height of the door panel, the height is about 1500mm, and the weight is heavy, so install 3 hinges.

 

2. Determine the position. Determine the installation position, first mark the door panel, and then drill a hole on it with a pistol. The drilling position should be about 5 mm away from the door edge, and the width of the installation hole should be about 35 mm. Pay attention to the depth. If the depth is not enough, the screws will easily loosen.

 

3. Install the hinge cup. After the position is determined, start to install the hinge cup. First, fix the hinge cup with particleboard self-tapping screws.

 

4. Install the hinge seat. Then install the hinge seat, select the European-style special screws for the particle board, fix the hinge seat, and press it directly on the door panel with a machine.

 

5. Test after installation. After the hinge seat is installed, insert the hinge into the cup hole of the door panel, open the hinge, and then fix the base with screws. After the installation work is completed, the cabinet door can be opened and closed back and forth.

 

How to install the hinge What is the hinge connection

 

Hinge, which is what we usually call a hinge, is a mechanical device used to connect two solids and allow relative rotation between the two. It can be used to make some precision instrument products, and it can also be used in daily life. It is applied in daily life, such as our common cabinet doors, they often use the hinge connection method, and with the choice of materials, good results can be achieved, and the hinges are often made of alloy materials, and the surface has been specially treated Sand blasting treatment, so it will not rust in the later stage, and the service life is relatively good. Next, you might as well follow the editor to learn about the information about hinge installation.

 

 

 

the

1. Ranking of hinge brands

 

 

Ranked No. 1: Aosite (English: Blum)

 

 

Ranked second: Hettich (English: Hettich)

 

 

Ranked third: Dongtai (English: DTC)

 

 

Ranked fourth: HAFELE (English: HAFELE)

 

 

Ranked fifth: Huitailong (English: hutlon)

 

 

Ranked sixth: ARCHIE (English: ARCHIE)

 

 

 

the

2. What is a hinge connection

 

 

A hinge, also known as a hinge, is a mechanical device used to connect two solids and allow rotation between them. A hinge may be composed of movable components, or it may be composed of foldable materials.

 

 

Hinges are mainly installed on doors and windows. Hinges are more installed on cabinets

 

 

According to the material classification, it is mainly divided into stainless steel hinges and iron hinges

 

 

In order to let people get better enjoyment, hydraulic hinges have appeared, which are characterized by a certain amount of cushioning and reduce noise to the greatest extent.

 

 

 

the

3. How to install the cabinet door hinge

 

 

1. Minimum door margin:

 

 

First of all, we need to determine the minimum door margin between the cabinet doors to be installed, otherwise the two doors are always "fighting", which is not beautiful and practical. The minimum door margin depends on the type of hinge, hinge cup margin and cabinet Select the value based on the thickness of the door. For example: the thickness of the door panel is 19mm, and the edge distance of the hinge cup is 4mm, so the minimum door edge distance is 2mm.

 

 

2. Selection of the number of hinges

 

 

The number of cabinet links selected should be determined according to the actual installation experiment. The number of hinges used for the door panel depends on the width and height of the door panel, the weight of the door panel, and the material of the door panel. For example: a door panel with a height of 1500mm and a weight between 9-12kg, 3 hinges should be used.

 

 

3. Hinges adapted to the shape of the cabinet:

 

 

The cabinet with two built-in rotatable pull baskets needs to fix the door panel and the door frame at the same time. The most important thing is that the built-in pull basket determines its opening angle to be very large, so the curvature of the hinge must be large enough to ensure that it can Freely open the cabinet door to a suitable angle, and conveniently take and place any items.

 

 

4. Selection of hinge installation method:

 

 

The door is divided according to the position of the door side and the side of the side panel, and there are three installation methods: full cover door, half cover door and embedded door. The full cover door basically covers the side panel; the half cover door covers the side panel. The half of the board is especially suitable for cabinets with partitions in the middle that need to install more than three doors; the embedded doors are installed in the side boards.

 

 

5. The whole process of cabinet door hinge installation:

 

 

Hinge Cup Installation Method Hinge Seat Installation Method Cabinet Door Hinge Installation

 

 

6. Adjustment of the door panel:

 

 

By loosening the fixing screw on the hinge base, slide the position of the hinge arm back and forth, and there is an adjustment range of 2.8mm. After the adjustment, the screw must be tightened again.

 

 

Front and rear adjustment of the ordinary hinge seat: by loosening the fixing screw on the hinge seat, and sliding the position of the hinge arm back and forth, there is an adjustment range of 2.8mm. After the adjustment is completed, the screws must be re-tightened.

 

 

Using the front and rear adjustment of the cross-shaped quick-mounted hinge seat: there is an eccentric cam driven by a screw on this cross-shaped quick-mounted hinge seat. The rotating cam can be adjusted within the range of -0.5mm to 2.8mm without loosening other parts Fixing screws.

 

 

Using the front and rear adjustment of the in-line quick-mount hinge seat: There is an eccentric cam driven by a screw on this in-line quick-install hinge seat, and the rotating cam can be adjusted within the range of -0.5mm to 2.8mm without loosening other parts. Fixing screws.

 

 

Door panel side adjustment: After the hinge is installed, before any adjustment is made, the door margin should be 0.7mm. In this way, the adjustment screw on the hinge arm can be adjusted within the range of -0.5mm to 4.5mm. If thick For door hinges or narrow door frame hinges, this parameter range is reduced to -0.15mm.

 

 

 

In addition to introducing the concept of hinge connection, the installation method is also given above. From this, we can know that as a common practice, it can play the role of connection and fastening on the one hand, and on the other. On the one hand, it can also support consumers and friends to carry out later mobile operations. In addition, hinges can be divided into stainless steel hinges or iron hinges according to their materials. According to post-processing operations, they can be further divided. For friends in different fields , you can choose hinge products with rich sizes and specifications and guaranteed service life.

 

How to install the cabinet door hinge

 

1: Think about the installation process first. (Not at all, you can refer to the existing similar cabinet doors for more observations) 2: Measure the size, buy the corresponding hinges and screws (there are many hinge styles). 3: Prepare Power tools, drill bits with a slightly flat bottom, easy to punch holes (the diameter depends on the shape of the hinge), flat and cross screwdrivers. 4: Specify the hinge position, the parallel and vertical positions between the hinges must be right, and the outside of the hinge and the screw Draw lines and dots on the hole position, (otherwise the adjustment will be troublesome after installation, and the aesthetics will be worse) 5: First install the hinge on the door 6: Then install the hinge on the door frame, 7: Adjust the gap to achieve a beautiful appearance

 

What are the installation methods of aluminum alloy door hinges

 

The hinge is used to fix the door panel, so the installation of the hinge is very important. So, what are the installation methods of the aluminum alloy door hinge? Let's take a look.

 

 

 

Aluminum alloy door hinge installation method

 

 

 

1. Look at the hinge type clearly

 

 

 

Before installation, it is very important to see the type of hinge clearly. Because there are so many types of hinges, each type has different installation methods. If you do not understand clearly and install blindly, it is easy to install wrongly, which will waste time and money. energy.

 

 

 

2. Determine the opening direction of the door

 

 

 

Then determine the opening direction of the door. If the door opens to the left, the hinge should also be installed to the left. If the door is to open to the right, the hinge should be installed to the right.

 

 

 

3. Measure the size of the door

 

 

 

After that, measure the size of the door. The main purpose is to determine the installation position of the hinge. The two hinges on the door must be aligned and a certain distance should be kept. Mark the door first, and then use tools to open it. groove.

 

 

 

4. Fixed hinge

 

 

 

After the groove on the door is opened, the next step is to install the hinge. First install the hinge seat on the door panel and fix it firmly with screws to prevent it from falling off. Then fix the leaf panels to the corresponding positions, and When fixing, it can be fixed by welding or by self-tapping screws.

 

 

 

What to pay attention to when installing hinges

 

 

 

1. Installation location and quantity

 

 

 

If the door at home is relatively heavy, it is recommended to install 3 hinges, while ordinary doors only need to install 2 hinges. Be careful not to install it at the junction of the corners of the door and window, and it should be installed at the tenth of the door and window body. One place should be divided evenly to prevent uneven installation.

 

 

 

2. Grasp the gap distance

 

 

 

In order to make the door installation look better, you must grasp the distance between the door panel and the hinge, usually the gap should be kept at 3-5 mm, if the distance is too close, it will also affect the use of the door.

 

 

 

I conclude: the above is about the installation methods of aluminum alloy door hinges, I believe everyone understands it! The installation of aluminum alloy door hinges needs to master many methods. If you don't know how to install, you can refer to the above content.