If you're on the hunt for high-quality cabinet hinges to enhance the functionality and aesthetic appeal of your home, look no further than the top manufacturer...

How to install drawer slide rail





The installation method is as follows:


1. When installing the drawer slide rail, it is necessary to disassemble the inner rail from the main body of the drawer slide rail. The method of disassembly is also very simple. There will be a spring buckle on the back of the drawer slide rail. The rail is removed.


2. Install the outer rail and middle rail part of the split slideway on both sides of the drawer box first, and then install the inner rail on the side plate of the drawer.


3. When installing the slide rail, it is recommended to assemble the drawer into a whole. There are two kinds of holes on the rail for adjusting the up and down and front and rear distances of the drawer. At the same time, ensure that the left and right slide rails are at the same horizontal position, and there should be no difference. big.



4. Then install the inner and outer rails, fix the inner rails to the length of the drawer cabinet with screws at the measured position (note that the inner rails and the already installed and fixed middle rails and outer rails should maintain the same position).


5. Tighten the corresponding holes of the two screws respectively, as shown in the figure below.


6. Follow the same method on the other side, but pay attention to keep the inner rails on both sides horizontal and parallel.


7. After installation, pull the drawer and try it. If there is any problem, you need to readjust it. If the drawer is smooth, it will be fine.


Extended information:


Rail classification


1. Roller type


This kind of slide rail has been around for a long time. It is the first generation of silent drawer slide rail. Since 2005, it has been gradually replaced by steel ball slide rail on the new generation of furniture. Composed of pulleys and two rails, it can meet the needs of daily push and pull, but the bearing capacity is poor, and it does not have the function of buffering and rebounding. It is often used on computer keyboard drawers and light drawers.


2. Fully pull out the steel ball slide rail


Steel ball slide rails are basically two-section or three-section metal slide rails. The most common structure is installed on the side of the drawer. The installation is relatively simple and saves space. Good-quality steel ball slide rails can ensure smooth sliding and large load-bearing capacity. This kind of slide rail can have the function of buffer closing or pressing rebound opening. In modern furniture, steel ball slide rails are gradually replacing roller slide rails and become the main force of modern furniture slide rails.


3. Hidden slide rail


This type of slide rail has hidden slide rails, horse riding slide rails and other types of slide rails, which are medium and high-end slide rails. The gear structure is used to make the slide rails very smooth and synchronous. This type of slide rails also has cushioning closing or pressing rebound The opening function is mostly used in middle and high-end furniture. Because the price is relatively expensive and it is relatively rare in modern furniture, it is not as popular as steel ball slide rails. This type of slide rail is the future trend.


4. Damping slide rail


The damping slide rail is one of the slide rails, which refers to providing a sound-absorbing and buffering effect that utilizes the buffering performance of the liquid and has an ideal buffering effect. The fast, easy and optimal automatic selection of the slide rail is included.


Reference source: Baidu Encyclopedia - Slide Rail


How to install drawer slides

Drawer slide rail is a very common but commonly used building material in home decoration. It is suitable for various cabinets such as wardrobes, TV cabinets, bedside tables, wine cabinets, cabinets, etc., which brings convenience to home life. However, if the drawer slides Improper installation of the rails will cause a lot of trouble when used, and even affect the atmosphere of the entire home life. The following editor will take you to understand how to install the drawer slide rails in order to reduce unnecessary troubles in daily life.

Related Recommendations ·Pictures of Oupai Cabinet ·Shenluda Sink ·Melamine Board

Drawer slide introduction

Drawer slide rails are commonly used accessories in furniture. The guide rails used for the movement of drawers or other moving parts are often equipped with bearings. The material of drawer pulleys determines the comfort of drawer sliding. Plastic pulleys, wear-resistant nylon, and steel balls are the most common. Three types of drawer pulley materials, quiet, comfortable and smooth when sliding, is the best way to distinguish the quality of the slide rail.

For cabinets, if the hinge is the heart of the cabinet, then the slide rails are the kidneys. Whether large and small storage drawers can be pushed and pulled freely and smoothly depends entirely on the support of the drawer slide rails. Generally, the bottom drawer slide rails are more The side drawer slides are good, and the overall connection with the drawer is better than the three-point connection.

Drawer slide installation

The hidden three-section drawer slide rail has an adjustment nail structure. When installing, use the adjustment nail to adjust the height of the drawer, and then lock the drawer with the locking nail of the damping slide rail. The drawer can be pushed and pulled freely. If you want to remove the drawer, just Pull out the locking pin of the slide rail, and the drawer can be lifted and separated from the slide rail.

76 Drawer slide rail installation First, determine what kind of drawer slide rail to use. Generally, three-section hidden slide rail is used. Please determine the length of your drawer and the depth of the counter according to certain data to select the corresponding size. Installed on the drawer.

77 Secondly, assemble the five boards of the drawer and screw on the screws. After the drawer panel has a card slot, after processing, place the drawer on the installed drawer, make the adjustment nail holes match, and then lock the lock. Tight nails push in to lock drawers and slide rails.

78 Finally, to install the cabinet body, you need to screw the plastic holes on the side plate of the cabinet body first, and then install the track removed from the top, and use two small screws to fix each slide rail one by one. Both sides of the cabinet must be installed and fixed.

Editor's note: After the drawer slide rails are installed, align the ends of the movable rails (inner rails) on both sides of the drawer side plate with the ends of the fixed rails (middle rails), and then gently push them inward, and you will hear When there is a light click, it means that the movable rail and the fixed rail have been linked, and the drawer can be pushed and pulled freely.

How to install drawer slides

1. For the furniture drawers made on the woodworking site, drawer pulleys must be installed. We must first determine what the track of the drawer is, determine the length of the drawer, and then select the size of the slide according to the corresponding specifications.

2. The installation method of the drawer can be divided into low drawer and inner drawer. The drawer panel of the low drawer still protrudes outside after the drawer is fully pushed into the box body and is not in a straight line up and down. The drawer panel of the inner drawer is fully pushed in the drawer. After entering the box, it also enters it at the same time, and will not stay outside.

3. The drawer slideway is divided into three parts: movable rail (inner rail), middle rail, fixed rail (outer rail)

4. Before installing the slideway, it is necessary to remove the inner rail, that is, the movable rail, from the main body of the slideway. Be careful not to damage the slideway during disassembly. The method of disassembly is very simple. Find the circlip on the inner rail and press it lightly. Remove the inner rail.

5. Install the outer rail and middle rail part of the split slideway on both sides of the drawer box first, and then install the inner rail on the side panel of the drawer. If it is finished furniture, both the box body and the side panel of the drawer There are pre-drilled holes by the manufacturer for easy installation. If it is made on site, you need to punch the holes yourself.

6. Finally, put the drawer into the box. When installing, pay attention to press the clip spring of the inner rail mentioned above, and then slowly push the drawer into the box in parallel and to the bottom. The movable rail and the fixed rail have been linked , the drawer can be pushed and pulled freely.

Precautions for installing drawer slides

1. The first is the choice of size. Generally speaking, the length of the slide rail of the drawer should be the same as the length of the drawer drawer. If the slide rail is too short, the drawer cannot reach the maximum opening and closing. If it is too long, it will cause failure. Install.

2. For the drawer slides, the installation is relatively simple. The key is how to dismantle them. In some pictures of how to disassemble the drawer slides, there are more detailed dismantling steps. Through these steps, it can be dismantled very well. , so if it is time to install, then you can reverse the thinking and restore it step by step from the dismantling steps, then you will know how to install the drawer slide rails. How to install the drawer rails


Drawer track installation method:


1. Reserve touch rebound space


If the furniture is made on-site by the carpenter, then remember to reserve some space for the drawer to bounce back before installing the drawer slides. Of course, if you choose finished furniture, you dont need to consider this issue.


2. Determine the installation method


There are two types of drawer installation: low drawer and inner drawer. The difference between the two is that after the drawer panel of the low drawer is fully pushed into the furniture cabinet, it still protrudes outside and is not in a straight line up and down. The inner drawer is The drawer front also goes into the drawer when it is fully pushed into the box and does not stay outside.


3. Clear slide track


In general, drawer slides can be divided into three parts: active track, middle track and fixed track.


4. Disassemble the movable track


Before installing the drawer slide, first find the circlip of the movable track of the drawer, press the circlip and gently remove the movable track from the main body of the slide. Note: During the disassembly process, do not damage the slide Do not disassemble the outer track and the middle track, otherwise there will be problems in subsequent installation and use.


5. Install the drawer track


Because the drawer slides are composed of outer rails, inner rails and middle rails, you need to install these rails one by one. First, install the outer rails and middle rails in the split slides on both sides of the drawer cabinet , and then install the inner rails to the side panels of the drawer.


Here you need to pay attention: if you are installing a drawer made on site, you need to pre-drill holes on the cabinet body and side panels of the drawer; if it is a finished piece of furniture, you don't need to punch holes.


6. Put the drawer into the box


After all the slides are installed on the drawer cabinet, the last step is to install the drawer into the cabinet. This step is relatively simple, but it should be noted that when installing, press the front inner track spring, and then Then slowly push the drawer into the cabinet parallel to the bottom.


Precautions for disassembly and assembly of drawers


1. The disassembly and assembly of the drawer track is not too complicated. We also need to remember the order of disassembly. When installing, we can also reinstall it in the opposite order.


2. Because most of the cramps are made of wood, you should not use too much brute force during demolition. You should also pay attention when using a screwdriver. Do not use the screwdriver to touch the wood, so as to prevent the surface of the drawer from being scratched. Bad will affect the beauty.


3. If you need to buy a new track after dismantling the track, you should also pay attention to whether the new specification and size are suitable for installation. If the specification and size are not suitable, or if it fails during the installation, there is no way to install it. Go up, otherwise it will bring you some troubles in the process of using it.


4. When disassembling the drawer track, it is also necessary to separate the drawer from the track, otherwise it may cause damage to the drawer, which will also cause some troubles for later use.

How to install the slideway of the drawer only needs 6 steps!

How to install the slides of the drawers? Drawers play a powerful storage role in people's daily life. A certain piece of finished furniture in every family must have drawers, but how are the drawers installed? Before understanding the installation of drawers, First of all, you need to know how to install the slideway of the drawer? Let's take a look together!

Drawer slide installation method and steps:

1. Reserve touch rebound space

If the furniture is made on-site by the carpenter, then remember to reserve some space for the drawer to bounce back before installing the drawer slides. Of course, if you choose finished furniture, you dont need to consider this issue.

2. Determine the installation method

There are two types of drawer installation: low drawer and inner drawer. The difference between the two is that after the drawer panel of the low drawer is fully pushed into the furniture cabinet, it still protrudes outside and is not in a straight line up and down. The inner drawer is The drawer front also goes into the drawer when it is fully pushed into the box and does not stay outside.

3. Clear slide track
In general, drawer slides can be divided into three parts: active track, middle track and fixed track.




4. Disassemble the movable track

Before installing the drawer slide, first find the circlip of the movable track of the drawer, press the circlip and gently remove the movable track from the main body of the slide. Note: During the disassembly process, do not damage the slide Do not disassemble the outer track and the middle track, otherwise there will be problems in subsequent installation and use.

5. Install the drawer track

Because the drawer slides are composed of outer rails, inner rails and middle rails, you need to install these rails one by one. First, install the outer rails and middle rails in the split slides on both sides of the drawer cabinet , and then install the inner track to the side panel of the drawer. Here also need to pay attention: if you install the drawer made on site, you also need to pre-drill the holes on the cabinet body and side panel of the drawer; if it is For finished furniture, no drilling is required.

6. Put the drawer into the box

After all the slides are installed on the drawer cabinet, the last step is to install the drawer into the cabinet. This step is relatively simple, but it should be noted that when installing, press the front inner track spring, and then Then slowly push the drawer into the cabinet parallel to the bottom.

The above is the introduction of relevant knowledge about "how to install the slide of the drawer". I hope it will be helpful to everyone.



How to install the drawer slide rail in the cabinet

Remove the inner rail of the slide rail, install the outer rail and middle rail part of the split slide on both sides of the drawer box, and drill holes in the drawer box and side panels. Then install the slide Then install the inner rail on the side panel of the drawer and fix it with screws to ensure that the rails on both sides of the box are installed at the same horizontal position.

Whether the drawer can be pushed and pulled freely and smoothly, and how it bears weight depends entirely on the support of the slide rails. The bottom slide rail is better than the side slide rails, and the overall connection with the drawer is better than the three-point connection. The material, principle, structure, and The technology varies widely, and the high-quality slide rail has small resistance and long service life.

Slide rails, also known as guide rails and slideways, refer to hardware connection parts fixed on the cabinet body of furniture for the drawers or cabinet boards of furniture to enter and exit. Slide rails are suitable for wooden and Drawer connections for furniture such as steel drawers.

The material of the pulley determines the comfort when the drawer slides. Plastic pulleys, steel balls, and wear-resistant nylon are the three most common pulley materials. Among them, wear-resistant nylon is the top grade. When sliding, it is quiet and silent. Depending on the quality of the pulley, you can use a Push and pull the drawer with your fingers, there should be no harshness and no noise.



Detailed explanation of drawer slide rail installation method

I believe everyone has drawers at home. Drawers are a very common furniture in our homes. When we use drawers, we need the cooperation of drawer slides. Drawer slides are also a very common building material in home decoration. It In addition to being suitable for drawers, it is also suitable for wardrobes or TV cabinets. In general, drawer slides are a very practical object. How should we install drawer slides after we buy them? The following introduces How to install drawer slides.


the
Drawer slide rail installation method


1. The slide rail of the drawer is fixed on a certain track for the movement of other moving parts of the drawer, with a groove or curved guide rail. The size of the drawer slide rail is generally available in the market: 10 inches, 12 inches, 14 inches , 16 inches, 18 inches, 20 inches, 22 inches, 24 inches. You can install different sizes of slide rails according to the size of each drawer model.


2. First fix the five boards of the assembled drawer, and screw on the screws. The drawer panel has card slots, and there are two small holes in the middle for installing the handle.



3. To install the drawer slide rails, you first need to disassemble the rails. The narrow ones are installed on the drawer side panels, and the wide ones are installed on the cabinet body. To distinguish before and after.


4. Install the cabinet. Screw the white plastic hole on the side plate of the cabinet first, and then install the wide track removed from above. One slide rail is fixed with two small screws one at a time. Both sides of the body must be installed and fixed.



the
Notes on installation:


1. Please ensure that there is a gap of 13mm between the drawer and both sides of the cabinet.


2. Fully stretch the three-section slide rail, there is a black buckle on the reverse side of the inner rail, press it to the left to separate the inner rail.


3. Fix the outer rail and middle rail on both sides of the drawer.



4. Fix the inner rails on both sides of the cabinet.


5. Hold up the drawer, align the middle rail with the inner rail and slide it in to the end.


6. After the drawer slide rails are installed, align the ends of the movable rails (inner rails) on both sides of the drawer side plate with the ends of the fixed rails (middle rails), and then gently push them inward, and you will hear a light A light click indicates that the movable rail and the fixed rail have been linked, and the drawer slide rail is installed.



When we install the drawer slide rails, we need to ensure the distance between the drawer and the cabinet body. This distance is preferably 13 mm. Otherwise, the installation will not be successful. You can follow the steps mentioned in the article step by step during installation. .After we have installed the drawer slide rails, we need to align the movable rails on both sides of the drawer, and then try to see if it can slide easily. If it can slide, it proves that the drawer slide rails are installed successfully. Everyone can Feel free to use it.



Through this visit, had a deeper and more comprehensive understanding of our company and .
AOSITE Hardware follows the heart and concentrates on its craftsmanship. We combine traditional craftsmanship with modern technology to produce various styles of Metal Drawer System. They are of high hardness and tear resistance after polishing with fine workmanship. They have strong luster and oxidation resistance. The color is not easy to fade. Such products are highly recognized in the market.


If you're looking to install drawer slide tracks in your video cabinet, this FAQ article will guide you through the process with a helpful diagram.