Single slot

It can be divided into two categories, large single slot and small single slot. Generally, those with a length greater than 75-78cm and a width greater than 43-45cm can be called large double grooves. It is recommended that a large single slot is recommended when the room space permits, the length is preferably above 60cm, and the depth is above 20cm, because the size of the general wok is between 28cm-34cm.

Onstage

The installation method is the simplest. After you reserve the location of the sink in advance, put the sink directly in, and then fix the joint between the sink and the countertop with glass glue.

Advantages: Simple installation, higher load-bearing capacity than the under-counter basin, and convenient maintenance.

Disadvantages: It is not easy to clean the surrounding area, and the edge silica gel is easy to mold, and water may leak in the gap after aging

Understage

The sink is embedded under the countertop and matched with a waste disposer. It is very convenient for daily use to directly sweep the kitchen waste on the countertop into the sink.

Double slot

The partition is clear, you can wash the dishes while washing the dishes, increasing the efficiency of housework.

Divided into large double slot and small double slot, the two are matched, it is more convenient to use.

Affected by factors such as the new crown pneumonia epidemic and the conflict between Russia and Ukraine, many countries are suffering from high inflation. In response to the impact of high inflation, mainly due to rising energy and food prices, many central banks have recently raised benchmark interest rates. Some analysts believe that, given that the inflation situation will continue for a long time, continuous interest rate hikes during the year are a certainty.

According to data from the Office for National Statistics on the 23rd, due to factors such as rising energy prices, the UK consumer price index (CPI) rose by 6.2% in February compared with the same period last year, the highest increase since March 1992.

The ECB's current baseline forecast for the average level of inflation this year believes that the inflation rate will be around 5.1%. European Central Bank President Christine Lagarde recently warned that euro zone inflation could exceed 7 percent this year as the conflict between Russia and Ukraine pushes up energy and food prices.

A joint announcement by the Monetary Authority of Singapore and the Singapore Ministry of Trade and Industry on the 23rd showed that the MAS core inflation rate (excluding accommodation costs and private road transport prices) fell to 2.2% in February from 2.4% in January, and the overall inflation rate From 4% to 4.3%.

According to the announcement, global inflation is expected to remain high for some time and will not gradually ease until the second half of 2022. In the near term, heightened geopolitical risks and tighter supply chains will continue to push up crude oil prices. Affected by factors such as geopolitical tensions and global transportation bottlenecks, supply and demand imbalances in commodity markets are also likely to persist.

What material is good for the hardware handle?(1)

When using all kinds of furniture in life, it is inseparable from the hardware handle. There are many materials for it. What kind of hardware handle should we choose when buying?

What material is good for the handle

1. Copper hardware handle: It is one of the most widely used materials, because the mechanical properties of copper materials are better, and the corrosion resistance and processing performance of copper are better. In addition, the color of copper is also relatively bright, especially for forged copper handles, which have a flat surface, high density, no holes, and no trachoma, which are very popular in the market.

2. Aluminum alloy hardware handle: the strength and rust resistance are relatively poor, but aluminum alloy materials are easy to produce more complicated pattern parts, especially die-casting parts. Most of the relatively complex handles on the market are aluminum alloys.

3. Ceramic material handle: the best rigidity of the material, the hardness of this material is usually 1500hv. The compressive strength is high, but the tensile strength of the material is low. In addition, the plasticity of ceramic materials is relatively poor, and it is not easy to oxidize. In addition, the material has good corrosion resistance to acids and alkali metal salts.

4. Stainless steel hardware handle: the material is more durable and brighter in use. In addition, the strength of stainless steel is better, the corrosion resistance is also strong, and the color will not change for a long time. Therefore, many users choose stainless steel hardware handles.

Easy Steps to Install Door Hinges like a Pro

Door hinges are an integral part of any functioning door, allowing it to swing open and close seamlessly. With a wide range of sizes, styles, and materials on the market, installing hinges might seem like a daunting task. However, armed with the right tools and a little patience, the process can be straightforward and hassle-free. This article will provide you with a step-by-step guide on how to install door hinges, ensuring a smooth and efficient installation process.

Step 1: Precise Measurement and Marking

The first crucial step in installing door hinges is accurate measurement and marking on both the door and the door frame. Using a measuring tape, pencil, and square, carefully mark the desired hinge placement by measuring the distance from the top and bottom of the door. This measurement is critical as it ensures that the door swings smoothly and fits snugly within the frame.

Place the hinge on the mark and trace its outline with the pencil. Repeat this process for the remaining hinges. It is essential to ensure that all hinges are placed at the same height and are level on both the door and the door frame. Proper alignment is key to a door that opens and closes without any hitches.

Next, position the door on the door frame, ensuring proper alignment, and mark the hinge position on the door frame using a square for straightness. Repeat this step for the second hinge. Again, double-check that the placement of the hinges matches that of the door. This will guarantee a proper fit once the hinges are installed.

Step 2: Drilling the Holes

Once the hinge locations are marked, you can move on to drilling the necessary holes. Choose a drill bit slightly smaller than the screws that came with your hinges. The holes should be deep enough to hold the screws firmly but not so deep that they puncture through the other side of the door or frame.

Start by drilling pilot holes on the marked spots on both the door and the door frame. Make sure to drill straight down into the wood, allowing the screws to go in straight. This ensures a secure and stable attachment of the hinges. After drilling the pilot holes, use a larger drill bit corresponding to the size of the screw head to create a counter-bore. The counterbore will enable the screw heads to sit flush with the hinge's surface, providing a polished and professional look.

Step 3: Installing the Hinges

With the holes drilled and the counterbores in place, it is time to install the hinges. Begin by positioning the hinge on the door and secure it with screws. However, avoid fully tightening the screws at this stage, leaving them slightly loose for potential adjustments if needed. This step allows for flexibility in case any alignment issues arise during the installation.

Once one hinge is securely attached, place the door in the frame by aligning it with the marked placement. Hold it in position and attach the other half of the hinge to the door frame in the same manner as before. Again, refrain from tightening the screws entirely.

To ensure the hinges are aligned correctly, open and close the door. If the door doesn't close properly, you may need to adjust the hinge placement on either the door or frame. This step might require some trial and error, but it is crucial to achieve a smooth and seamless operation of the door.

Once you have ensured everything is properly aligned, tighten all the screws. Be sure not to overtighten as this could strip the holes or affect the door's movement. Test the door's opening and closing to ensure it functions smoothly with no obstructions or resistance.

Step 4: Finishing Touches

After securely attaching the hinges, you can complete the installation process by sanding the door edges and applying paint or stain as desired. This step enhances the door's aesthetics and provides protection against wear and tear.

Additionally, you may need to make slight adjustments to the latch or strike plate to guarantee smooth and easy closing and locking of the door. These final adjustments ensure that the door fits snugly within the frame and provides optimal security.

Although installing door hinges may initially appear complex, it is, in fact, a straightforward process that anyone can successfully accomplish with the right tools and some patience. By carefully following our step-by-step guide, complete with precise measurements, accurate marking, drilling pilot holes, and counterboring, you can ensure the proper installation of your door hinges. Take the time to perform each step correctly, and you'll enjoy the benefits of a smoothly operating door for years to come.

There is currently a wide variety of door and window hardware brands in China, making it challenging to determine the top ten. However, I will provide a brief overview of ten reputable brands in no particular order:

1. Huangpai Doors and Windows: Known for system doors, windows, and sunshine rooms, this brand is backed by Guangdong Huangpai Home Furnishing Technology Co., Ltd.

2. Hennessy Doors and Windows: Specializing in high-end, customized, and system doors and windows, this brand is a leader in aluminum alloy and silicon-magnesium alloy products.

3. Paiya Doors and Windows: Foshan Nanhai Paiya Doors and Windows Products Co., Ltd. is known for its innovative hollow glass swing doors and hanging sliding doors.

4. Xinhaoxuan Doors and Windows: This Foshan-based company not only offers a wide range of products but has also expanded into the real estate industry, demonstrating its strength.

5. Paled Windows and Doors: Established in 1995, Paled is one of the earliest and largest producers of system doors and windows in China. Its wood-like aluminum alloy series has gained recognition for its design, quality, and environmental sustainability.

6. Yihe Doors and Windows

7. Jijing Doors and Windows

8. Moser Doors and Windows

9. Milan Windows

10. Ozhe Doors and Windows

These brands have made a name for themselves through their dedication to quality and innovation in the door and window industry. To explore further, feel free to conduct your own research on the top ten brands of door and window hardware in China.

However, it's worth noting that door and window hardware accessories play a vital role in the overall functionality and aesthetics of doors and windows. When choosing these accessories, it's essential to opt for reputable brands that offer durability, ease of use, and complement the overall design of your home.