Single slot

It can be divided into two categories, large single slot and small single slot. Generally, those with a length greater than 75-78cm and a width greater than 43-45cm can be called large double grooves. It is recommended that a large single slot is recommended when the room space permits, the length is preferably above 60cm, and the depth is above 20cm, because the size of the general wok is between 28cm-34cm.

Onstage

The installation method is the simplest. After you reserve the location of the sink in advance, put the sink directly in, and then fix the joint between the sink and the countertop with glass glue.

Advantages: Simple installation, higher load-bearing capacity than the under-counter basin, and convenient maintenance.

Disadvantages: It is not easy to clean the surrounding area, and the edge silica gel is easy to mold, and water may leak in the gap after aging

Understage

The sink is embedded under the countertop and matched with a waste disposer. It is very convenient for daily use to directly sweep the kitchen waste on the countertop into the sink.

Double slot

The partition is clear, you can wash the dishes while washing the dishes, increasing the efficiency of housework.

Divided into large double slot and small double slot, the two are matched, it is more convenient to use.

Over time, door hinge pins can become rusted or corroded, causing difficulties in opening and closing doors. If you find yourself in this situation, don't worry. This article will guide you through the step-by-step process of removing door hinge pins effectively.

Essential Tools Needed for Removing Door Hinge Pins

Before we begin, gather the following tools:

1. Hammer: A hammer is necessary for tapping and loosening the hinge pins.

2. Needle-nose pliers: These pliers will be used to remove any cap located at the top of the hinge pin.

3. Screwdriver: A screwdriver is needed to tap and loosen the hinge pins.

4. Lubricant: Use a lubricant such as WD-40, PB Blaster, or a similar product to dissolve any rust or corrosion.

5. Replacement hinge pins: If your inspection reveals rust or corrosion, it is advisable to replace the hinge pins. Make sure to have replacement pins ready if necessary.

Step-by-Step Guide to Removing Door Hinge Pins

Follow these steps to remove door hinge pins successfully:

Step 1: Inspect the Hinge Pins

Firstly, take a close look at the hinge pins to check for signs of rust or corrosion. This inspection will help you determine if you need to replace the hinge pins alongside removing them.

Step 2: Lubricate the Hinge Pins

Generously spray the lubricant onto the hinge pins. Allow a few minutes for the lubricant to penetrate and dissolve any rust or corrosion. This step ensures easy removal of the hinge pins.

Step 3: Position the Hinge Pin

Make sure the hinge pin is visible and securely in place. This can be achieved by fully opening the door to expose the top of the hinge pin. It is crucial to have a clear view and access to the pin.

Step 4: Remove the Pin Cap

Using needle-nose pliers, carefully remove the cap located at the top of the hinge pin, if there is one. This cap may be present for added protection and needs to be taken off before removing the pin.

Step 5: Remove the Pin

With the cap removed, it's time to remove the hinge pin. Place the screwdriver near the base of the pin and gently tap it with the hammer. This action gradually loosens the pin, allowing it to come out. Make sure to apply firm and controlled taps to avoid any damage.

Step 6: Remove the Hinge Pin

Once loosened, wiggle the hinge pin back and forth until it can be fully removed from the hinge. This may require a bit of patience and effort, but it will eventually come out.

Step 7: Repeat the Process

Repeat Steps 3-6 for each hinge pin that needs to be removed. Take your time and be thorough in removing all the pins in order to have a smooth operation of the door.

Step 8: Replace the Hinge Pins (If Necessary)

If your inspection revealed rust or corrosion, it is advisable to replace the hinge pins. Insert the new pins into the hinge and tap them into place using the hammer and screwdriver. Ensure they are securely in place before proceeding.

While removing door hinge pins may seem challenging, with the correct tools and a little patience, it can be done quickly and effortlessly. By following these comprehensive steps, you can successfully remove and replace the door hinge pins, ensuring smooth operation of your door once again.

Expanding on the existing article, it is important to emphasize the importance of regular maintenance to prevent rust and corrosion on door hinge pins. It is recommended to periodically lubricate the hinges to prevent future problems. Additionally, inspecting the pins and hinges for any signs of damage can help identify issues early on and avoid cumbersome repairs down the line. Moreover, considering the theme of home improvement and repair, it is worth mentioning the significance of safety measures while performing maintenance tasks. Always use proper protective equipment, such as gloves and eye goggles, to avoid any potential injuries. By taking a proactive approach to door hinge maintenance, you can ensure the longevity and smooth operation of your doors.

In order to continue to polish the "good hardware, made by Jinli" brand, from June 17th to 19th, Jinli Town, Gaoyao District, Zhaoqing City will hold the China Zhaoqing (Jinli) Traditional Dragon Boat Competition and the first Jinli Hardware International Expo, with more than 300 booths It will be exhibited on the industrial avenue of the hardware intelligent manufacturing town.

Guangdong AOSITE Hardware Precision Manufacturing Co., Ltd. (hereinafter referred to as "AOSITE") is a "national high-tech enterprise". type enterprise. Focusing on home hardware manufacturing for 30 years, it has a modern production base covering an area of over 13,000 square meters, a marketing center of 200 square meters, a product testing center of 200 square meters, a product experience hall of 500 square meters and a logistics center of 1,000 square meters. Taking the opportunity of the first Jinli Hardware International Expo, we sincerely invite businessmen from all walks of life to come to the exhibition for a visit and exchange with the ingenuity and quality of 30 years of painstaking efforts! In the future, we will continue to focus on the R&D and innovation of home hardware products, and create new hardware qualityism with ingenuity and innovative technology.

At the first Jinli Hardware International Expo, AOSITE will focus on promoting soft up gas spring, one way three-dimensional hydraulic damping hinge, metal drawer box, double spring damping slide rail and other heavyweight products.

Taking advantage of the opportunity of this expo, in the future, AOSITE will continue to make efforts in the design, development and production of complete fittings and smart home supporting hardware, continue to increase investment, and continue to provide strong brand and technological support for downstream home furnishing companies. Bigger and stronger the brand influence of "good hardware, made by Jinli".

Gaoyao Jinli is a strong industrial town in our city. It has outstanding people and clustered industries. It faces Sanshui District of Foshan City across the river. . The town currently has more than 5,800 enterprises and self-employed individuals. There are more than 300 categories and more than 2,000 varieties of hardware products produced in the town. 30% of the products are exported to Europe, America, the Middle East, Africa and Southeast Asian countries. The industrial structure is basically formed.

The first grand International Hardware Expo held in June will further open the door for the development of Jinli hardware industry chain and make friends all over the world for local enterprises. At the same time, the gold-lettered signboard of "good hardware, made by Jinli" will be further polished!

The first Jinli Hardware International Expo, AOSITE Hardware is looking forward to your participation!

Invisible doors have become a popular choice for modern homeowners, thanks to their sleek design and seamless integration with interior spaces. These doors offer enhanced security and functionality with their innovative features. This article explores the various aspects of invisible doors, including their thickness, hidden hinges, door closers, three-way cut-off openings, and electronic locks.

Door Thickness:

One of the crucial considerations when selecting an invisible door is its thickness. To ensure durability and sturdiness, these doors usually have a thickness ranging from three to four centimeters. This thickness provides ample strength, guaranteeing long-term usage without compromising security.

Lotus Leaf Concealed Door Closer and Electronic Locks:

The hidden door features of invisible doors contribute significantly to their aesthetic appeal. Among them, the lotus leaf concealed door closer goes unnoticed, adding to the seamless appearance of the door. Additionally, three-party collection ports house electronic locks, which provide advanced security measures where access control is necessary.

Choosing Hinges and Door Closers:

When it comes to enhancing the functionality of invisible doors, the choice between ordinary hinges and hydraulic hinges with door-closing function can be perplexing. While ordinary hinges may prove to be cost-effective, hydraulic hinges offer greater convenience. Their ability to automatically close the door reduces wear and tear on hinges and ensures a controlled and gentle closure.

Installation Process:

Once the invisible door is manufactured and ready for installation, the process becomes relatively straightforward. If the door factory has already drilled the hole, homeowners can easily decorate the door as per their preferences. The installation involves these steps:

1. Install the chute on the door frame, ensuring proper positioning for the upper and lower ends of the hidden door closer.

2. Determine the door's opening direction and adjust the door closer's speed accordingly, allowing for control and customization.

3. Install the support arm securely, ensuring it aligns with the locking screw at the positioning connection end in the upper chute of the door frame.

4. Perform a left adjustment on the 1.2-speed adjustment, gradually increasing the closing force for optimal functionality.

Invisible doors with hidden hinges, concealed door closers, three-way cut-off openings, and electronic locks provide an elegant and secure solution for modern homeowners. With a thickness ranging from three to four centimeters, these doors prioritize durability and longevity. Adhering to proper installation guidelines, including the use of hydraulic hinges with door-closing function, ensures optimum performance and convenience. By choosing invisible doors, homeowners can seamlessly integrate style and functionality into their interior spaces while enjoying enhanced security measures.

Hidden door hinges with door closers are a popular choice for those who want a seamless and sleek look for their doors. But what are some common questions about these hinges and closers? Let’s explore some FAQs about hidden door hinges with door closers.

Sliding doors are commonly used in workshops due to their space-saving design and ease of use. This article will guide you through the process of installing sliding doors on composite panel walls of steel structure workshops, offering step-by-step instructions for a successful installation.

Step 1: Inspect the Products

Before starting the installation, carefully check the sliding door products and spare parts to ensure they are in good condition.

Step 2: Prepare the Workspace

Lay the door frame material facing up on a protected surface to avoid scratches. It is recommended to place cardboard or carpet on the ground.

Step 3: Install the Sliding Door on the Hanging Rail

Place the upper sliding wheels into the correct order in the upper chute. Assemble the frame and horizontal frame accurately and secure them with half-section self-tapping screws. Pay attention to the position of the pulley to avoid rework.

Step 4: Place the Installed Door Frame

Hang the left and right door frame edge seals horizontally and vertically. Punch holes for positioning and secure them with expansion screws. Adjust the gap with a thin plate if too large.

Step 5: Install the Transom Window (if applicable)

For transom windows, align them horizontally and vertically and fix them with expansion screws. If the gap is too large, use thin wood chips. Slide the door upwards and fix the transom window with screws. Without a transom, drill the appropriate position on the upper chute and fasten with a top screw.

Step 6: Fine-tune the Door Frame

Ensure the door frame is aligned, leveled, and vertical. Secure all screws tightly.

Step 7: Hang the Sliding Door on the Rail

Check if the pulleys are at the same height and match the site's height. Adjust if necessary. Hang the sliding door on the rail, ensuring the correct orientation.

Step 8: Adjust the Level and Install Positioning Wheel

Fine-tune the level of the upper pulley. Install the positioning wheel on the sliding door according to the installation position determined in the vertical state. Fix it with the correct screw.

Step 9: Finalize the Installation

Check the evenness of the gap between the two doors. Fine-tune if necessary and ensure the door leaf is level, the lock functions correctly, and the waving effect is smooth and safe. Secure positioning wheel screws, tighten upper sliding wheel adjustment screw, and reinstall the sliding door.

Step 10: Maintenance and Clean-up

Cover all holes with plugs. Spray self-spraying wax on the upper sliding suspension wheel, locks, and other parts to reduce noise and increase smoothness. Clean the surface and surroundings for proper sanitation.

Installing sliding doors on composite panel walls of steel structure workshops requires careful preparation and precise execution. By following these step-by-step instructions, you can ensure a successful installation and enjoy the many benefits offered by sliding doors.

Extended Information:

Sliding doors are versatile and cater to various needs, from traditional plate surfaces to glass, fabric, aluminum alloy profiles, and more. They are widely used in workshops, factories, warehouses, and many other applications.

Maintenance tips:

Regularly clean the tracks and avoid heavy objects hitting them. Use non-corrosive cleaning fluid. If mirrors or panels are damaged, seek professional assistance for replacement. Check the anti-jump device regularly. If the door is not tight against the wall, adjust the lower pulley screw.

If you're having trouble with the sliding door track on your steel structure workshop, here are some tips on how to fix the slide rail on the composite.