Guide to Buy Double Wall Drawer System in AOSITE Hardware

The sliding rail of the cabinet drawer is related to whether the cabinet drawer can be pushed and pulled freely and smoothly, to what extent, the load bearing, and whether it will tip over. From the current technology, the bottom drawer slide rail is better than the side slide rail, and the overall connection with the drawer is better than the three-point connection. The materials, principles, structures, and craftsmanship of the drawer slides are very different. The high-quality slides have low resistance, long life and smooth drawers.

1. Pay attention to the structure and material of the drawer slide

The most important thing to buy cabinet drawer slides is good load-bearing. Among them, the drawer slides that are connected as a whole are the best, and the three-point connection is the second, and it must be easy to disassemble. For drawer slides, inferior materials have a fatal impact on the quality of the slides. When purchasing, you must carefully feel the slides of different materials with your hands, and choose slides with a solid feel, high hardness and heavier.

2. According to the needs of your own kitchen cabinets, buy the right model

When buying cabinet hardware accessories, they must be matched with the cabinet. Therefore, the model requirements for drawer slides and other accessories are extremely strict. The length of the slide rails and the requirements for drawers are key considerations. If the drawer is to put very heavy things, pay great attention to the load-bearing capacity of the drawer slide rail and the approximate number of push and pull that the slide rail can withstand under load.

Rewritten

Installing the Self-Priming Slide Rail for Wardrobe Drawers

To install the self-priming slide rail for wardrobe drawers, follow these steps:

1. Fix the five boards of the assembled drawer using screws. The drawer panel should have a card slot, and there should be two small holes in the middle for installing the handle.

2. Disassemble the slide and install the narrow one on the drawer side panels, while the wide ones are installed on the cabinet body. Make sure the bottom of the slide rail is flat with the bottom of the drawer side panel, and the front is flat with the front of the drawer side panel. Pay attention to the front and rear orientation.

3. Finally, install the cabinet body.

Checking and Accepting the Wardrobe Installation

When checking and accepting the wardrobe installation, consider the following factors:

Appearance:

- Observe whether the wardrobe's appearance meets the requirements. Check the color and texture of the overall furniture paint process, ensuring coordination and smoothness. Check if the color of the outer paint falls within the allowable range of color difference. Also, examine the smoothness of the paint surface, looking for bubbles or imperfections.

Craftsmanship:

- The manufacturing process of the wardrobe is crucial. Check the connection between each part, including plates and hardware, ensuring reasonable and strong connections. Whether horizontal or vertical, the connection points within the wardrobe's structure should be tightly combined without gaps. The opening and closing of drawers and doors should be flexible, with no degumming or burrs.

Structure:

- Pay attention to whether the wardrobe's structure conforms to specifications. Ensure the frame of the wardrobe is correct and firm by gently pushing it and checking for looseness. Verify that the vertical surface is perpendicular to the ground at a 90-degree angle, and the horizontal plane connected to the ground is flat enough.

Door Panel:

- Check if the door panel is installed properly, with consistent height and gap width when closed. Ensure that the door handles are on the same horizontal line. If it's a push-pull door panel, verify that the door panels can slide smoothly without detaching from the slide rails.

Drawer:

- Inspect the drawers and ensure they function properly without derailing or collapsing. Check that each drawer can perform its duties during use.

The Connection of Wardrobe Cabinets:

The wardrobe is connected using 3-in-1 screws. The backboard is generally connected using millet nails. The cabinet boards are usually made of standard 18mm compressed solid wood particles. They are linked by 3-in-1 three-dimensional hardware that can be disassembled infinitely without affecting the link's firmness. There are two main methods for the backboard: insert board and nail board, with the insert board being the most reasonable choice.

Living in the Wardrobe after Installation:

After the wardrobe is installed, it generally has no smell, and you can move in immediately. However, if there are concerns, allow two to three days for the wardrobe to dry before moving in, or perform a formaldehyde test. To remove formaldehyde, open the doors and windows for ventilation, use green plants that can absorb formaldehyde, brew black tea and put it in the living room, or place activated carbon in different corners of the home.

AOSITE Hardware, Quality Comes First:

AOSITE Hardware is a brand that prioritizes quality. With a focus on quality control, service improvement, and fast response, AOSITE Hardware remains the top brand in the industry. The company invests in innovative production technology and product development to stay competitive. AOSITE Hardware's products, such as drawer slides and hinges, are known for being anti-radiation, UV-resistant, and of high quality. The company is dedicated to providing unique clothing and improving its brand image. AOSITE Hardware does not accept merchandise returns unless they are defective.

Here are the steps to install a wardrobe drawer self-priming slide rail:
1. Measure the dimensions of the drawer and the available space in the wardrobe.
2. Attach the slide rail to the sides of the drawer using screws.
3. Position the drawer in the wardrobe and mark the spots for the slide rail on the wardrobe sides.
4. Secure the slide rail to the wardrobe using screws.
5. Test the drawer to ensure it opens and closes smoothly.
If you have any further questions, feel free to contact our customer service for assistance.

Types of Furniture Drawer Slides

When it comes to selecting the right drawer slides for your furniture, it's important to be aware of the different types available. Choosing the correct type of drawer slide is essential to ensure smooth and safe operation. In this article, we will discuss the various types of drawer slides and their specifications, allowing you to make an informed decision when purchasing.

What are Drawer Slides?

Drawer slides, also referred to as drawer glides or runners, are hardware components that enable drawers to open and close smoothly in furniture pieces such as cabinets, office cabinets, and bathroom cabinets. They provide the necessary support and stability for the movement of drawers, ensuring ease of use.

Specifications of Drawer Slides

Drawer slides come in various specifications and sizes to cater to different furniture needs. The most common sizes available in the market include 10 inches, 12 inches, 14 inches, 16 inches, 18 inches, 20 inches, 22 inches, and 24 inches. These sizes accommodate different drawer dimensions, allowing you to choose the appropriate slide rail length for your specific requirements.

Types of Drawer Slides

1. Steel Ball Type Slide Rails: Steel ball slide rails are the most popular choice for modern furniture. These two-section or three-section slide rails feature steel balls that ensure smooth push and pull, along with a substantial bearing capacity. They are easy to install on the side of drawers, saving space. Steel ball slide rails can also provide cushioning closing or rebounding to open, adding functionality to the furniture.

2. Gear Type Slide Rails: Gear type slide rails, including hidden slide rails and horse riding slide rails, are considered medium to high-end options. These slide rails use a gear structure to offer synchronized and smooth movement. Like steel ball slide rails, gear type slide rails can provide cushioning closing or rebounding to open. Due to their relatively higher cost, they are commonly used in middle and high-end furniture.

3. Roller Slide Rails: Roller slide rails are the first generation of silent drawer slide rails. They are composed of one pulley and two rails, providing satisfactory functionality for daily push and pull. However, roller slide rails have low load-bearing capacity and lack the cushioning and rebounding functions found in other types. As such, they are mostly used for computer keyboard drawers and light drawers and have been gradually replaced by steel ball slide rails in modern furniture.

4. Wear-Resistant Nylon Slide Rails: Nylon slide rails are characterized by their excellent wear resistance. They ensure smooth and quiet drawer movement, with a soft rebound. While fully nylon slide rails are relatively rare in the market, there are numerous slide rails available that incorporate nylon components for enhanced performance.

When selecting drawer slides for your furniture, consider the specific requirements of your drawers and the desired level of functionality. Whether you opt for steel ball, gear type, roller, or wear-resistant nylon slide rails, choose the appropriate size and ensure they are installed correctly for optimal performance. By making an informed choice, you can improve the usability and longevity of your furniture drawers.

There are several types of furniture tracks, including ball bearing, roller, and undermount slides. Drawer slides come in various types such as side mount, center mount, and European slides.

At AOSITE Hardware, we strive to provide the utmost quality and customer service. In this article, we will guide you through the process of installing two-section drawer track rollers for your computer desk drawer. By following these steps, you can ensure a smooth and hassle-free installation.

Step 1: Assemble the Track

Start by pulling the track apart, making sure to align the sections properly. Pass a screw through the hole of the track and attach it securely to the computer table using a screwdriver. It is important to note that both tracks need to be at the same height. To ensure accuracy, use a ruler to measure and mark the height before installation.

Step 2: Positioning the Drawer

Next, position the drawer in its intended location. Using a screwdriver, attach the track to the outside of the computer desk, ensuring a secure connection between the track and the drawer. Take your time to align the components accurately for proper functionality.

Step 3: Installing the Drawer Slides

To install the drawer slides, follow these instructions:

1. Remove the inner rail from the main body of the drawer slide rail. Install both the outer rail and inner rail on each side of the drawer box before proceeding.

2. Fix the inner rail onto the side panel of the drawer. Ensure that the left and right slide rails are at the same level for optimal performance. Secure the inner rail to the drawer's inner rail using screws.

3. Pull the drawer to check if it moves smoothly. If the drawer slides with ease, the installation is complete.

By meticulously following these steps, you can successfully install two-section drawer track rollers for your computer desk drawers. With AOSITE Hardware's reliable products and exceptional customer service, you can rest assured knowing your drawers are functioning seamlessly. As a reputable leader in the hardware market, AOSITE Hardware is valued and recognized both domestically and internationally for its comprehensive capabilities.

Are you having trouble installing your drawer track roller two-section slide rail? Check out our installation video for step-by-step instructions on how to properly install and use the roller drawer slide rail.