How to remove the drawer from the slide rail
The operation method is as follows:
The first step is to pull out the drawer with both hands, and pull the drawer to the end, as shown in the figure below:
The second step, then raise your hands in front of the drawer, and lift it up slightly in the direction indicated by the arrow, as shown in the figure below:
The third step, then you can lift the drawer out, as shown in the figure below:
The fourth step, the drawer is disassembled successfully, as shown in the figure below:
How to disassemble the drawer slide rail
Do you know what is a drawer slide? Now many people use drawers, and the drawer slide is a kind of slide installed in the drawer, mainly for the convenience of drawer pulling. The drawer slide has been used for a long time. There will be wear and tear. When there is a problem with the drawer slide rail, it needs to be removed for replacement. Many people don't know how the drawer slide rail is removed. How to install it. Let's learn about the installation and installation of the drawer slide rail The method of disassembly. Friends who want to know how to disassemble can take a look.
the
1. How to remove the drawer slide rail
1. In the first step, everyone pulls the drawer as far as possible, and a long black tapered buckle appears at this time.
2. In the second step, use your hand to press down the black protruding strip buckle (downwards in most cases, lifting up is not ruled out), and the long strip buckle will be stretched. At this time, you can feel the slide rail loosened.
3. In the third step, press down on both sides of the long buckle at the same time, and pull out both sides while pressing the long buckle with both hands, and the drawer will come out.
4. Fourth, this is the rendering of the final drawing. The black buckle is separated. If you just take things, you dont need to pull the drawer out completely, you can go in and take it with your hands.
5. Fifth, it is also very simple to install the drawer back. You only need to push the drawer back along the track, and the black buckle will automatically connect with the original card slot. Push it in to the end, and then pull it back. free.
2. Introduction of drawer slide rails
Drawer slide rails are commonly used accessories in furniture. The guide rails used for the movement of drawers or other moving parts are often equipped with bearings. The material of drawer pulleys determines the comfort of drawer sliding. Plastic pulleys, wear-resistant nylon, and steel balls are the most common. Three types of drawer pulley materials, quiet, comfortable and smooth when sliding, is the best way to distinguish the quality of the slide rail.
3. How to install drawer slide rails
To install drawer slide rails, first determine what kind of drawer slide rails to use. Generally, three-section hidden slide rails are used. Please determine the length of your drawer and the depth of the counter according to certain data, so as to select the corresponding size and install it on the drawer. .
Secondly, assemble the five boards of the drawer, screw on the screws, the drawer panel has a card slot, after processing, put the drawer on the installed drawer, make the adjustment nail holes coincide, and then push the locking nails in Lock drawers and slides.
Finally, to install the cabinet, you need to screw the plastic holes on the side panel of the cabinet first, and then install the track removed from the top. One slide rail is fixed with two small screws one after the other. The two sides of the cabinet Both sides must be installed and fixed.
The above is the disassembly and installation method of the drawer slide rail. Do you know how to disassemble the slide rail now? The disassembly and installation of the drawer slide rail is very simple. When there is a problem with the drawer in our home, we can check the drawer. Slide rail, see if the slide rail of the drawer is broken or damaged. If there is a problem with the slide rail of the drawer, it must be removed and replaced with a new one, so that it will not affect the use of our drawer. When disassembling Wear gloves to avoid cutting your hands.
The method of removing the slide rail drawer is as follows:
First pull out the drawer and pull it to the longest position, then you can see the buckle on the track. There will be a button on it, and you can hear a click when you press it down with your hand. At this time, the drawer slide rail has been Loosen, and then pull the drawer out hard to take it out.
Pull the drawer to the maximum, and a black buckle will be exposed on the track. While pushing the buckle up with your hand on the left slide rail, pull the drawer outward to pull out the whole buckle. Conversely, the right slide rail While pushing the buckle down by hand, pull the drawer outward to pull out the whole buckle. Pull out the buckles on both sides and continue to pull the drawer, and the drawer can be easily removed.
Rail introduction
Slide rails, also known as guide rails and slideways, refer to hardware connection parts fixed on the cabinet body of furniture for the drawers or cabinet boards of furniture to enter and exit. Slide rails are suitable for wooden and Drawer connections for furniture such as steel drawers.
From the current technology point of view, the bottom slide rail is better than the side slide rail, and the overall connection with the drawer is better than the three-point connection. The materials, principles, structures, and processes of the drawer slide rails vary widely, and the high-quality slide rails have small resistance and long life. , the drawer is smooth. The steel ball slide rail is basically a two-section or three-section metal slide rail. The more common structure is installed on the side of the drawer. The installation is relatively simple and saves space.
The above content refers to: Baidu Encyclopedia - How to remove the drawer of the slide rail
The slide rail drawers can be removed in the following ways:
1. Pull the drawer outward with your hands first, then you can see a long black buckle.
2. Press the buckle down with your hand, it will become longer, and you can also feel the slide rail become loose.
3. While pressing, pull the drawer outward, so that the drawer will be removed.
Types of drawer slides:
1. Roller slide rail
This kind of slide rail is also called powder spraying slide rail. Its components are relatively simple, usually consisting of 1 pulley and 2 tracks. This kind of slide rail has relatively poor load-bearing capacity and is mainly installed on relatively light drawers. It will not affect the use of the slide rail.
2. Steel ball slide rail
This is also a common type of slide rail, which is mainly set on the side part of the drawer and has a 2-section metal device. The installation method of this slide rail is relatively simple, and the slide rail does not take up too much space inside. It is the same as Compared with the roller slide rail, the function is relatively strong, with functions such as buffer closing and pressing to open.
3. Gear slide rail
There are many types of this type of slide rail, one of which is a hidden form of slide rail, which is very smooth when sliding. The function of the gear slide rail is also more, and it also has functions such as buffering. This kind of slide rail is mainly used in relatively high-end On the furniture, so the price is more expensive, not so widely used.
4. Damping slide rail
This is a special kind of slide rail, which is commonly used in furniture drawers. It uses the hydraulic buffer performance to slow down the closing speed of the drawer. When the drawer is closed, it will use the hydraulic function to reduce the speed and prevent the drawer from colliding. .
How to remove the drawer track
The first step is to prepare the drawer tracks that need to be removed, as shown in the figure below:
The second step, and then pull the drawer track to the end, as shown in the figure below:
Step 3: After pulling to the end, you can see the black button in the red box, as shown in the figure below:
The fourth step, then pinch the black button, as shown in the figure below:
The fifth step, after that, the drawer track can be disassembled, as shown in the following figure:
How to take out the bottom track drawer
Steps to take out the track drawer when mopping the floor:
1. Find the slide rail at the bottom of the drawer. There is a pin on one side of the slide rail as a fixation. The direction indicated by the red arrow in the figure below is the fixed pin inside the red frame.
2. Gently pull out the pin on the drawer slide rail. The bottom track will have no fixed pin. The direction indicated by the arrow in the picture below is the red circle in the picture.
3. Pull open the drawer and lift it up, and the bottom-supporting track drawer will be taken out. Lift up in the direction indicated by the arrow in the figure below.
How to remove the slide drawer
The slide drawer disassembly method is as follows:
Tool material:
Various drawers with rails (slides)
Specific steps:
1. Pull the drawer outwards with your hands first, then you can see a long black buckle. Press the black buckle and press down. Most of the cases are downward, and upwards are not ruled out. The long buckle will stretch,
The rails will feel loose.
2. Press the bayonet on both sides at the same time, press down, press the long buckle with both hands, and pull both sides outward at the same time, put your hands in, the black buckle will separate, if you just take things, you dont need to put all the drawers
Pull it out, hand can go in and take it out.
3. On the right slide rail, push the buckle down with your hand and pull the drawer outward at the same time to pull out the whole buckle. After pulling out the buckles on both sides, continue to pull the drawer, and you can easily put it out Drawer pulls are removed.
Types of drawer slides
1. Roller slide rail
This kind of slide rail is also called powder spraying slide rail. Its components are relatively simple, usually consisting of 1 pulley and 2 tracks. This kind of slide rail has relatively poor load-bearing capacity and is mainly installed on relatively light drawers. It will not affect the use of the slide rail.
2. Steel ball slide rail
This is also a common type of slide rail, which is mainly set on the side part of the drawer and has a 2-section metal device. The installation method of this slide rail is relatively simple, and the slide rail does not take up too much space inside. It is the same as Compared with the roller slide rail, the function is relatively strong, with functions such as buffer closing and pressing to open.
3. Gear slide rail
There are many types of this type of slide rail, one of which is a hidden form of slide rail, which is very smooth when sliding. The function of the gear slide rail is also more, and it also has functions such as buffering. This kind of slide rail is mainly used in relatively high-end On the furniture, so the price is more expensive, not so widely used.
How to remove the drawer track
Three-section drawer rail disassembly steps:
1. Pull the drawer as far as possible, and you will see a long black tapered buckle.
2. Press down or lift up the black protruding strip buckle by hand, the long strip buckle will be stretched, and the slide rail will be loose at this time
3. Press down the strip buckle on both sides at the same time, pull both sides outward, and the drawer will come out
4. It can be removed
Three-section drawer rail installation steps:
1. The drawer slide rail can be divided into three parts: the outer rail, the middle rail, and the inner rail
2. When installing the drawer slide rail, the inner rail needs to be disassembled from the main body of the drawer slide rail. There will be a spring buckle on the back of the drawer slide rail, and the inner rail can be disassembled by pressing it lightly.
3. Note that the middle rail and the outer rail are not removable and cannot be removed by force
4. Install the outer rail and middle rail part of the split slideway on both sides of the drawer box first, and then install the inner rail on the side panel of the drawer. If it is finished furniture, pre The drilled holes are easy to install, you need to drill the holes yourself
5. When installing the slideway, it is recommended to assemble the drawer into a whole. There are two kinds of holes on the track for adjusting the up-down and front-back distance of the drawer. At the same time, ensure that the left and right slide rails are at the same horizontal position, and there should be no difference. big
6. Then install the inner and outer rails, fix the inner rails to the length of the drawer cabinet with screws at the measured position (note that the inner rails and the already installed and fixed middle rails and outer rails should maintain the same position)
7. Tighten the holes corresponding to the two screws respectively
8. Follow the same method on the other side, but pay attention to keep the inner rails on both sides horizontal and parallel
9. Note that if the middle rail and the outer rail are not level at the left and right sides in the previous step, at this time there will be a situation where the casing cannot be pushed forward. At this time, either check the position of the outer rail, or adjust the position of the inner rail to match the position of the outer rail.
10. After installation, pull the drawer to try, if there is any problem, it needs to be readjusted
Precautions:
Key points for slide selection
1. Test steel
How much the drawer can bear mainly depends on whether the steel of the track is good or not. Drawers of different specifications have different thicknesses of steel and different load-bearing. When purchasing, you can pull out the drawer and press it with your hands to see if it will loosen and slam. Crank or flip.
Second, look at the material
The material of the pulley determines the comfort when the drawer slides. Plastic pulleys, steel balls, and wear-resistant nylon are the three most common pulley materials. Among them, wear-resistant nylon is the top grade. When sliding, it is quiet and silent. Depending on the quality of the pulley, you can use a Push and pull the drawer with your fingers, there should be no harshness and no noise.
How to remove the rail drawer
Now many drawers are equipped with guide rails, which allow the drawers to slide easily. However, the guide rails are prone to wear and tear after being used for a long time. At this time, the guide rails need to be replaced, so how to remove the guide rail drawers? Let's learn together with me.
How to remove the rail drawer
1. First of all, the drawer should be pulled out to the maximum position, and then we can see a black and long tapered buckle.
2. Then you should press down the long buckle with your hands, and the long buckle will be stretched at this time, and we can also feel that the slide rail has become loose. Of course, some guide rails are lifted upwards, so Everyone must act according to the actual situation.
3. Next, we should press down the long buckles on both sides of the drawer together, and at the same time pull the drawer out with both sides, and then the drawer can be disassembled.
4. After the guide rail drawer is disassembled, it is very simple to install it back. You only need to push the disassembled drawer guide rail against the rail, and then the long buckle will be docked with the original card slot. Then just push the guide rail drawer to the innermost part of the track. If you feel that the drawer is not pulled very smoothly, you can pull the drawer back and forth several times, and you can move freely.
5. The removal of the drawer rails is also very simple, just remove the screws fixed on the drawer, so that the drawer and the drawer rails can be separated, and then remove the drawer rails from the cabinet, but be very careful when disassembling, so as not to damage the Damage to cabinets and drawers.
6. If you want to completely remove the guide rail drawer, you only need to remove all the screws fixed on the drawer track, then we can easily separate the drawer and guide rail. Then put the cabinet on the track and The screws can be removed.
The relevant content about how to disassemble the guide rail drawer is introduced here. In fact, the disassembly method of the drawer guide rail is very simple. It can be easily disassembled only by mastering certain skills. I hope the knowledge introduced above can help everyone.
How to remove the drawer How to remove the drawer from the slide rail
1. If you want to disassemble the drawer, first pull the drawer outward to the greatest extent so that you can see the long black plastic pointed buckles on the side of the slide rail, and then push the buckles on both sides of the drawer slide rail up and down at the same time. Press down or up and down, press and hold and pull the drawer back, you can disassemble the guide rail and take off the drawer.
2. Use a screwdriver to remove the two slide rails fixed inside the cabinet.
3. These two steps are sufficient, the overall process is relatively simple and convenient, and it can be easily removed without a special hardware master.
4. Of course, the structure of the slide rail used in the drawers of different families is also different. Some simple slide rails only need to pull the drawer to the end, and then lift it up to remove the entire drawer, which is easier to operate.
Our cooperate tenet is .The visit of our customers certifies our increasing popularity in the industry.As the pace of global economic integration is accelerating, AOSITE Hardware is fully prepared to integrate into the international environment.
As a standardized enterprise, AOSITE Hardware stands out in the global hardware market and is approved by many international institutions.
Sure! Here is an example of a "How to remove the rail drawer" FAQ article:"How to remove the rail drawer:1. Open the drawer fully2. Locate the levers or buttons on the rail3. Press or release the levers/buttons to disengage the drawer from the rail4. Carefully lift and pull the drawer out of the railAnd that's it! You have successfully removed the rail drawer.
Change market and language